Skip to content

10 inch vs 12 inch rough in toilet?

Are you a home improvement enthusiast considering a new toilet installation? If so, you may be wondering whether to go with a 10 inch or 12 inch rough in. The rough in is the distance from the wall behind the toilet to the center of the drain. Here are a few things to consider before making your final decision.

First, think about the size of your bathroom. If you have a small bathroom, a 10 inch rough in may be a better option. On the other hand, if you have a larger bathroom, a 12 inch rough in may give you a little more wiggle room.

Second, take into account the type of drain you have. If you have a standard drain, a 10 inch rough in should be sufficient. However, if you have a sloped drain, you may need a 12 inch rough in to ensure proper drainage.

Finally, think about your budget. A 10 inch rough in toilet will typically be less expensive than a 12 inch rough in toilet. So, if cost is a consideration, a 10 inch rough in may be the way to go.

Now that you know a little more about 10 inch vs 12 inch rough in toilets, you can make an informed decision about which option is right for your bathroom

There is no definitive answer to this question as it depends on a number of factors, including the specific dimensions of your bathroom and the location of the existing plumbing. In general, however, a 12 inch rough in toilet will provide more space and be less likely to require major adjustments to your plumbing.

Can you replace a 10-inch rough in toilet with a 12-inch rough in toilet?

If you’re considering a 10-inch rough-in toilet for your bathroom, be aware that it may not be compatible with a 12-inch rough-in. While a 10-inch rough-in toilet can plausibly fit into a 12-inch rough-in (though a longer connector may be needed), the same cannot be said for using a 12-inch rough-in toilet in a 10-inch rough-in. A 12” rough-in toilet will not fit in a bathroom with a 10” rough-in size.

See also  Drive medical preservetech universal raised toilet seat?

A 10-inch rough-in is the usual measurement installed in older homes. However, the 12-inch measurement is the standard for modern toilet plumbing. Most toilets that you encounter in retail outlets have 12-inch rough-in dimensions.

What does 12 rough in mean for a toilet

Toilet rough in dimensions are the space between the wall behind the toilet and the center of the waste pipe. Standard toilet rough in dimensions are 12 inches but can be anywhere from 10 to 14 inches in some cases.

A 12-inch rough-in for a toilet means that there is 12 inches between the center of the toilet flange to the finished back wall. Most toilets have a 12-inch rough-in size.

What is the most common toilet rough-in size?

The standard rough-in for toilets is 12 inches, though you may encounter 10-inch and 14-inch rough-ins in older homes. You should find the rough-in measurement in the new toilet’s product information. This will ensure that your new toilet will fit properly in the space.

The rough-in dimension is the distance from the wall to the center of the drain pipe. The most important measurement you can take for a replacement toilet is the rough-in dimension. This is because the toilet will need to be anchored to the floor at this point.

What height toilet is best for seniors?

The ADA specifies that the height of a disabled toilet must be between 17 and 19 inches. This is because comfort toilets are typically this height, and it is important for those with disabilities to have access to toilets that they can use comfortably.

Comfort height toilets are becoming more popular in both residential and commercial settings. As the name implies, comfort height toilets are taller than standard toilets, making them more comfortable for taller people and for those who have a hard time getting up from a low seat. Most comfort height toilets will measure 17 to 19 inches from the floor to the seat, making them compliant with ADA standards.

See also  Does vinegar dissolve toilet paper?

Is it better to have a low or high toilet

Comfort height toilets are becoming increasingly popular, as they offer a number of benefits over traditional toilets. The taller seat simply makes it easier to sit down and stand up, and the higher seat alleviates discomfort that comes from squatting down and cocking the knees out to the sides. A comfort height toilet is especially beneficial for taller people, seniors and anyone with knee or back pain.

If you’re looking for an excellent performing toilet, be sure to choose one with a score of 500 or above. This will ensure that your toilet functions well and provides the necessary flushing power.

Should toilet flange be flush with floor?

If you install the toilet flange on top of the finished floor, you can be sure that there won’t be any leak paths, because the flange will be at the correct height to accept the horn at the bottom of the toilet.

It is important to know the difference between an S-trap and a P-trap because they are both used for different purposes. An S-trap is typically used for toilets while a P-trap is used for sinks and other drainage purposes.

Does rough in have to be exact

When measuring a toilet’s rough-in distance, it is important to take into account the baseboard and not to measure from it. This will ensure that you get an accurate measurement and avoid buying the wrong fixture for your bathroom.

The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. The minimum distance in front of the toilet to the facing wall or fixture is 21 inches.

How far can my toilet be from the stack?

If your trap is more than 6 feet away from the vent, it may not work properly and could cause your drains to back up. Make sure to check the UPC for the proper distance between your trap and the vent.

See also  Black stuff on toilet seat after sitting?

The most common size for a toilet flapper is two inches, but three inch flappers have become popular in recent years and can be found in newer toilets manufactured since 2005. An easy reference for determining your toilet’s flapper size is to look at the flush valve drain opening at the bottom of your tank.

How do you know if your toilet is tight enough

If you’re trying to remove a toilet bowl, a good rule of thumb is to try a turn or two a side until you feel resistance. Then try to wiggle the toilet bowl slightly. If there’s no significant movement, you’re probably tight enough.

This tightening operation is a “feel” thing you get from experience, so be conservative and use your best judgement.

Most people find elongated toilet bowls to be more comfortable, but in a small bathroom, a round bowl can save space. Elongated toilet bowls measure up to 31″ from the wall, while round fixtures max out at 28″. Because round bowls are less expensive than elongated bowls, they save a few dollars, too.

What is the difference between standard and comfort height toilets

Comfort Height toilets are about 17 to 19 inches from the floor to the top of the seat. They are designed to have about the same seated height as a typical chair. Taller people typically prefer a Comfort height toilet.

Today’s high-efficiency toilets are a vast improvement over first-generation low-flow models. New technology and design advancements, such as pressure-assisted flushers and modifications to bowl contours, allow these newer toilets to flush better than their predecessors. As a result, homeowners can enjoy the water savings that come with high-efficiency toilets without sacrificing performance.

Conclusion

There is no difference between a 10 inch rough in toilet and a 12 inch rough in toilet. The rough in is the distance from the wall to the center of the drain. Most toilets have a rough in of 12 inches, but some have a rough in of 10 inches.

There is no definitive answer when it comes to deciding between a 10 inch or 12 inch rough in toilet. Ultimately, it depends on the specific needs and preferences of the homeowner. Some factors to consider include the size of the bathroom, the type of toilet needed, and the budget. 10 inch rough in toilets are typically less expensive, but may not be able to accommodate certain types of toilets. 12 inch rough in toilets provide more space and flexibility, but may be more expensive. Ultimately, it is important to carefully consider all factors before making a decision.