The bathtub spout pipe is an important part of your plumbing. It is the pipe that brings water to your bathtub from the main water supply. If you have a leak in your bathtub spout pipe, it can cause serious damage to your home.
A bathtub spout pipe is a pipe that is used to carry water from the tub faucet to the showerhead. The pipe is usually made of brass or copper and is connected to the water supply line with a compression fitting.
Table of Contents
What kind of pipe do you use for a tub spout?
Galvanized pipe is often used when a threaded pipe is required, since it’s a bit more durable than copper. Copper is a softer metal, and may not hold up as well against the potential abuse the spout could see.
When installing a slip-on tub spout, it is important to check the manufacturer’s specifications to ensure that you have the appropriate length of copper pipe. The pipe should be a minimum of 1″ and a maximum of 2-7/8″ in length, depending on the tub spout.
How do you replace a bathtub spout pipe
If you need to replace a slip-on spout, it’s easy to do. Just loosen the setscrew (usually with a hex wrench) and pull the spout off the copper pipe that protrudes from the wall. Twist the spout as you pull and be gentle so you don’t loosen any pipe connections inside the wall. Then slide on the new spout and tighten the setscrew.
This is the measurement for the length of your tub spout. The first measurement is from the back edge of the spout to the front where the threads start on the inside of the spout. The second measurement is from the surface of the wall to the back of the threaded elbow inside the wall. The total of the two measurements is the length of your tub spout plus 1/4 inch.
Can you use plastic pipe for tub spout?
CPVC can be used for your tub and shower drain if you want to use it for your water supply lines. You can use CPVC for the connection between the shower valve and the shower spout.
PEX piping is not designed to support the weight of a tub spout or to withstand the frequent use of the diverter. Copper, brass, or galvanized pipe is a better choice for a tub spout drop.
Can you use steel pipe for tub spout?
If you’re looking to save a few bucks, you can totally use a galvanized steel nipple instead of a brass one. Just be aware that over time, the steel will corrode and you’ll end up having to replace it sooner than you would if you had used brass.
If you select the wrong size tap connector, you could experience issues. Basin taps usually have a 15mm thread, but bath taps have a 22mm thread. Be sure to check the size of your tap before selecting a connector!
How big should a tub spout hole be
There are three main types of holes that are typically drilled in a tub: faucet holes, overflow holes, and drain holes. The faucet holes are the largest, at 1-1/4″ in diameter, while the holes drilled in the tub rim are 1″ in diameter. The overflow hole is usually the same size as the faucet holes, at 1-1/4″.
If your bathtub has two handles or a single handle design, the stems that connect to the pipes will need to be removed or replaced. Before detaching any parts, shut off the water supply to the house to prevent the plumbing from spraying.
Is it easy to change bath spout?
Whether you’re replacing an old bathtub spout or installing a new one, you’ll just need to determine if your spout is a thread-on model or one with a set screw. Once you know that, changing one out is pretty simple. If you’re not sure which type of spout you have, take a look at the base of the spout where it meets the wall. If there’s a small set screw visible, you have a set screw spout. If not, it’s probably a thread-on spout.
If you’re trying to remove a spout from a pipe, there are a few things you need to check first. Under the spout, where it meets the shower wall, see if there’s a set screw. The set screw will require either a hex key or screwdriver. If a screw exists, loosen it and slide the spout off the pipe.
What size stub out for tub spout
The Stub Out Nipple must be between 2” and 3” long. The end of the Stub Out Nipple should be even. Use Sandpaper to remove burrs and sharp edges from the end of the Tubing and to polish the Tube surface to a smooth, bright copper color. Slide the Adapter onto the Stub Out Nipple with the threads toward the wall.
If you have a gap between the back of your tub spout and the wall, it may be due to the fitting not being accurately placed. You can try screwing the tub spout into a female threaded fitting behind the wall, or onto a length of threaded pipe that has been screwed into the fitting.
Do you need Teflon tape for tub spout?
When working with a threaded connection, you will want to clean the threads on the nipple coming out of the wall with a wire brush. Then, apply either pipe-joint compound or Teflon tape to the threads. We prefer the Teflon tape for two reasons: it is cleaner and less messy to work with than pipe-joint compound.
PEX tubing is not recommended for use with tub spouts due to the restriction in 1/2″ PEX. 3/4″ PEX may be a better option, but faucet manufacturers have not considered this because the 3/4″ PEX to 1/2″ FIP fittings are not widely available.
What size PVC pipe is used for tub drain
A bath tub drain needs to be a minimum of 2 (horizontal) or 1 ½ (vertical) drain pipe size, with a minimum 1 1/2 vent pipe size. A lavatory requires a 1 ¼ minimum drain and vent pipe size.
PVC is a strong, durable plastic commonly used in construction. It is inexpensive and easy to work with. CPVC is a similar product, but it is made with a different process that gives it extra strength. It can withstand higher temperatures than PVC, making it ideal for hot water lines.
Can bacteria grow in PEX pipe
It is interesting to note that the PEX pipe showed a higher growth of coliform bacteria than copper pipe. This may be due to the fact that the levels of released metal from plastic pipes were monitored in five pipe systems, PB, PVC, PP, PE, and cPVC.
PEX water lines are made from a synthetic material that can slowly deteriorate when exposed to UV light for a long period of time. Even light bulbs can affect the lifespan of PEX water lines. PEX cannot be taken outside the house and exposed to UV light for a prolonged period of time.
Warp Up
The bathtub spout pipe is the pipe that connects the bathtub faucet to the water supply.
There are a few different types of bathtub spout pipes, but the most common is the U-shaped pipe. This pipe is usually made of brass or plastic and is attached to the wall with screws. The other type of pipe is the I-shaped pipe, which is also made of brass or plastic. This pipe is attached to the wall with brackets.