There are a few things you need to take into consideration when moving a toilet a few inches. The first thing is the water supply. You need to make sure that the water supply lines are long enough to reach the new location of the toilet. The second thing is the drain pipe. The drain pipe needs to be long enough to reach the sewer line. The third thing is the wax ring. The wax ring seals the connection between the toilet and the sewer line. If the wax ring is not sealed properly, you will have leaks.
If you need to move your toilet a few inches, you can do so by loosening the bolts that hold it in place and then lifting it up and over to the new location. Then, simply retighten the bolts to secure the toilet in its new position.
Table of Contents
How much does it cost to move a toilet over a few inches?
If you are planning on moving plumbing fixtures in your bathroom remodel, be prepared to spend between $2,500 and $3,500 per fixture. This can be a significant cost factor, so make sure to factor it into your budget.
You can move a toilet as far as you wish to. However, you may need to drill a new hole in the floor and install a new wastewater pipe. This will result in a lot of investment at your end. However, you can also move the toilet to a certain extent without having to change the waste line and stack.
How do you slightly move a toilet
Moving a toilet may seem like a daunting task, but with a little planning and some elbow grease, it can be done! Here are 8 simple steps to get the job done:
1. Make a plan
Before you start, it’s important to have a plan. Decide where you want the toilet to go, and make sure you have enough space to accommodate it. Then, gather the tools you’ll need, including a wrench, screwdriver, and pail.
2. Make space for the toilet
Clear out any obstacles from the area where the toilet will go. This will make it easier to maneuver the toilet into place.
3. Turn off the water
The next step is to turn off the water supply to the toilet. This will prevent any accidents while you’re working.
4. Remove remaining water
There will be some water remaining in the toilet bowl and tank. Use a pail to remove this water before you disconnect the supply line.
5. Disconnect the supply line from the toilet
Using a wrench, loosen the nut that connects the supply line to the toilet. Then, remove the line from the toilet.
6. Remove the bolts
There
A toilet offset flange is a product that gives you extra distance from the existing toilet sewage pipe. It works with both 3-inch and 4-inch sewage pipes.
Can you move a toilet 3 inches?
If you need to move your toilet more than just a couple of inches, you will have to demolish the concrete to access and relocate water and waste lines. Then you will have to rebuild the concrete foundation and replace the sub-flooring, flooring, and fixtures. This is a big project that will require professional help.
If you’re planning on moving your toilet, you’ll need to hire both an experienced plumber and a bathroom design professional. The main issues with moving the toilet involve plumbing problems, like changes to the drainage, venting, and water supply. You’ll also likely need to open up some spaces, like the floor or the wall.
How easy is it to reposition a toilet?
This job is by no means easy, but for many homeowners, it’s certainly doable. It will however require a fair amount of remodelling to get this done, and you’ll likely be tearing down a wall or two and even bringing up sections of the floor and fixtures.
The toilet and bidets must have a minimum space of 70cm in width and 120cm in length. If they are next to a wall, the minimum free space should be 20cm, and if there is an element on their side, they should not be placed less than 15cm away for greater usability.
What’s the minimum distance from toilet to sink
It is recommended that toilets have some elbow room between them and another fixture or vanity. The NKBA’s recommendation is at least 18″. Codes allow a minimum distance of 15″.
The minimum clearance from the center of the toilet to any adjacent fixture or sidewall is 15 inches. This means that when you are looking at the toilet, there should be at least 15 inches of clearance from the center of the toilet to any adjacent fixture (or wall).
Should a toilet be flush with the wall?
The toilet flange must be at least 15 inches away from any sidewall or nearby fixture. However, 15 inches is the absolute minimum. A 15-inch distance from the vanity, shower, tub and back and side walls are required to accommodate the toilet flange.
The UPC states that the distance between your trap and the vent should be no more than 6 feet. In other words, the vent needs to feed into the drain line within 6 feet of the trapways that connect to it in order for it to work properly.
Is it OK if toilet flange is flush with floor
It is best to install the toilet flange on top of the finished floor. If you install the toilet flange flush with the finished floor, or even below the finished floor, leak paths will form, because the flange won’t be at the correct height to accept the horn at the bottom of the toilet.
If your toilet flange is too short, you can use a toilet flange spacer or extender to raise it to the proper height. These spacers come in different sizes and some have rubber or silicone gaskets attached.
Can a plumber move a toilet?
If you’re planning on moving your toilet, it’s important to involve a professional plumber to help with the task. They will be able to properly move the drainage and water supply to the new location, ensuring that everything is installed correctly. This will help avoid any potential issues down the line and ensure that your toilet is properly functional.
You will not need planning permission to refit a kitchen, but building regulations may apply if you are adding a new bathroom.
Warp Up
There are a few different ways that you can move a toilet over a few inches, depending on your specific needs and situation. One way is to simply disconnect the water supply line and waste line from the toilet, then use a dolly or other moving device to slide the toilet over to the desired spot. You will then need to reconnect the water and waste lines. Another way is to unbolt the toilet from the floor flange, then use shims to raise the toilet up slightly and slide it over to the desired spot. Once it is in the correct spot, you can lower it back down and reattach it to the flange.
If you need to move your toilet a few inches, there are a few things you need to do. First, you need to turn off the water to the toilet. Next, you need to disconnect the supply line from the shut-off valve. After that, you need to disconnect the drain line from the toilet. Finally, you can lift the toilet and move it to the new location.