The Lyons company produces a wide variety of tub surrounds for the do-it-yourselfer. The instructions for installation are relatively easy to follow. However, there are a few things to keep in mind during the installation process. First, be sure to measure the tub area carefully before purchasing the surround. Next, follow the instructions included with the surround carefully. Most surrounds come with a template that will help you make the necessary cuts. Finally, use the provided screws and wall anchors to secure the surround in place. With a little care and attention to detail, your new Lyons tub surround will be installed in no time!
1. Turn off the water to your tub at the main water shutoff valve.
2. Remove the old tub surround.
3. Install the new tub surround following the manufacturer’s instructions.
4. Turn the water back on and test the tub for leaks.
Table of Contents
How to install Lyons linear shower walls?
When installing panels, it is important to check for a tight fit in each corner. Using shims if needed, check that each panel rests flat against the wall. This will ensure a professional looking installation.
When applying a tub surround adhesive, be sure to give the edges a continuous bead of adhesive. This will ensure that the tub surround is properly secured.
What is the easiest tub surround to install
If you’re looking for an inexpensive and easy-to-maintain option for your bathtub or shower enclosure, consider an acrylic or fiberglass surround kit. These kits are much easier to install than ceramic tile wall enclosures, and they provide a sleek, modern look that’s easy to keep clean.
Is it worth it to refinish a bathtub?
Refinishing a bathtub can be a great way to save money on a bathroom remodel. … In most cases, refinishing a bathtub is also less expensive than replacing it. Prices for bathtub refinishing can range from $200 to $1,000, depending on the size and condition of your tub, as well as your geographic location.
Is it hard to install a bathtub?
Installing a bathtub is not an easy job. You need to be comfortable working with tools, have some basic carpentry skills, and be able to lift a fair amount of weight. If you’re not confident in your abilities, it’s best to hire a professional.
Can you install a bathtub in a small bathroom?
Planning is crucial in a small bathroom. … A good rule of thumb is that a tub should be no more than 60 percent of the length of the room, leaving room for a walkway on each side.
Can you install a bathtub on a concrete floor?
Most bathtub surrounds are made of fiberglass or acrylic and can be installed on almost any type of flooring
Do you put drywall behind a direct to stud tub surround?
If you are planning on installing a tub or shower surround, it is important to note that most require direct-to-stud installation. This means that you will need to remove any existing drywall in order to access the studs. We recommend cutting the drywall to roughly the size of the surround to save yourself time in patching walls when you’re finished with the installation.
Since you intend to paint the surface, you can bring the sheetrock right down to the flange. However, if you’re going to tile over the surface, you should use backer board instead.
What do you put behind a tub surround?
Cement board or an equivalent moisture-resistant backing material should be installed on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints. Paper-faced backer board should not be used behind seamed tub and shower enclosures.
If you’re considering converting a room that was never a bathroom into a wet space, it’s important to keep in mind that drywall on its own is not suitable for use in bathrooms. This is because drywall is prone to absorbing moisture, which can eventually lead to the wall losing its structural integrity. Instead, it’s best to use a material that is specifically designed for wet spaces, such as tile or waterproof paneling.
How do you stick a tub surround
When you are working with adhesives, it is important to make sure that the adhesive is not too thick. You want to be able to align the back panel with the adhesive so that it is evenly distributed. If the adhesive is too thick, it can make it difficult to align the back panel and can also cause the back panel to not adhere properly.
If you’re looking for an easy and inexpensive way to remodel your shower or bathtub alcove, using glued surround panels is a great option. This is an especially good choice if the walls need a makeover but the shower base or bathtub is in otherwise good condition.
What is the most durable tub surround?
Composite tub surrounds and tubs are the strongest and have the longest projected life span. Most mount directly to bare studs with screws, nails or manufacturer-provided clips, although a few can be glued to a clean, smooth surface. This makes them ideal for high-traffic areas and homes with small children or pets.
It is important to make sure that the insulation behind your tub or shower is equivalent to the insulation in the rest of your exterior walls. This will help to ensure that your home is properly insulated and that heat is not escaping through your tub or shower. An air barrier of cement backer board, rigid foam insulation, or non-paper-faced drywall can help to provide a continuous air seal and prevent heat loss.
Can a plumber install tub surround
If you’re in need of a new bathtub, be sure to call a professional plumber. They will be able to take care of the installation and ensure that everything is properly connected. You’ll be able to enjoy your new bathtub in no time!
If you’re looking to install a tile tub surround, you can expect to pay between $1,000 and $1,500 for the labor. This includes the cost of setting materials and grout, as well as any cement board or waterproofing membrane that may be necessary. Tile cost is not included in this labor price.
Are tub surrounds easy to install?
1. Remove all old caulking and debris from around the perimeter of the tub or shower.
2. Using a utility knife, score the surface of the surround where you will be applying the new caulk.
3. Apply a bead of caulk around the perimeter of the tub or shower.
4. Place the new surround against the wall and press it into the caulk.
5. Use a level to make sure the surround is level, then use a pencil to trace around the perimeter.
6. Remove the surround and cut along the traced line with a saw.
7. Apply adhesive to the back of the surround, then place it back into position.
8. Use finishing nails or screws to secure the surround to the wall.
9. Caulk the joints between the surround and the tub or shower.
10. Apply a bead of caulk around the perimeter of the tub or shower to seal.
If you’re tiling your shower or tub surround, you’ll need to take some special steps to prepare the walls. First, apply a layer of 1/2″ thick cement backer board to the wall studs. Then tape any seams and corners with fiberglass tape. Next, apply thin-set adhesive over the fiberglass tape, and allow it to dry. Finally, roll a waterproofing sealer over the walls, and allow the sealer to dry. This will help ensure that your tile job lasts for years to come.
Conclusion
1. Remove all existing wall tiles and any adhesive material from the surface. Use a putty knife or another sharp tool to scrape off any old caulk or sealant from around the tub.
2. Measure the space where you will be installing the new tub surround. Make sure to measure the height of the space as well as the width. You will need to purchase a tub surround that is the same size or slightly smaller than the space you are measuring.
3. Cut any trim pieces that will be needed to fit around the tub surround. Use a saw to cut the trim to the desired length.
4. Apply a continuous bead of caulk or sealant around the edge of the tub. This will help to create a watertight seal.
5. Place the tub surround into the space and press it firmly into place. Use a level to make sure that the surround is level and plumb.
6. Apply more caulk or sealant around the perimeter of the tub surround, where it meets the wall.
7. Install any trim pieces that were cut earlier. Nail the trim into place using finishing nails.
8. Caulk or seal the area where the trim meets the wall
Overall, Lyons Tub Surround installation was a positive experience. The company was great to work with and the end result was a high-quality product that looks great and functions well. We would recommend this company to others.