Whether you’re wanting to update your tub’s look or repair a leaky faucet, replacing the tub spout is a relatively easy do-it-yourself project. To remove the old tub spout, start by unscrewing the diverter handle, if there is one, with a Phillips screwdriver. Next, use an Allen wrench or a screwdriver to remove the set screw that’s holding the spout in place. In many cases, you may be able to simply pull the spout off after removing the set screw. If the spout is stuck, insert a putty knife between the wall and the spout and gently pry it off. To install the new spout, first apply a bead of plumber’s putty or caulk around the base. Screw on the new spout (hand tight only) and then use the set screw to secure it in place.
A rear threaded tub spout is a type of spout that is attached to the back of a bathtub. This type of spout is often used in conjunction with a handheld showerhead.
Table of Contents
How do you remove a rear threaded tub spout?
When using a screwdriver to turn a tuff spout, be sure to hold the spout firmly with one hand to prevent it from turning.
There will be a small hole in the bottom of the tub spout, if you see a screw, you have a CC (Slip Fit) tub spout. If there is no screw, you have an IPS (threaded) tub spout. IPS (Threaded)-Threaded directly onto the pipe from the wall.
How do I know if my tub spout is threaded
If you see a tiny screw on the underside of the spout, you have a slip-on tub spout with a set screw. If there is no set screw, you have a threaded tub spout.
You might have to turn it a little bit to get it going on there. And then you’ll take a more natural grip on it and you’ll be able to get a good feel for how it’s working.
Do all tub spouts have a set screw?
If you have a screw-on type tub spout, you will need to remove the set screw to take the spout off. If your tub spout does not have a set screw, it is likely either push-on or slip-on.
If you need to remove or replace your bathtub’s handles, you’ll first need to shut off the water supply to your home. This will prevent any plumbing from spraying while you’re working. Once the water is shut off, you can then detach any parts that need to be removed.
Are all tub drains threaded?
There are two main types of tub drains- threaded and drop-in. Threaded drains are most commonly found in older tubs, while drop-in drains are more common in newer models. You can usually tell which type of drain you have by inspecting it. If the drain has screws or is threaded, it is likely a threaded drain. If the drain simply sits in a hole in the bottom of the tub, it is likely a drop-in drain.
A non-diverter tub spout is a type of tub spout that doesn’t have a mechanism to cause the flow of water to be diverted from the bath. This type of tub spout is less common than diverter tub spouts, but can be just as effective in directing water flow.
Can you just replace a tub spout
If you’re looking to replace a slip-on spout, the process is quite simple. All you need to do is loosen the setscrew (usually with a hex wrench) and pull the spout off the copper pipe that protrudes from the wall. Be sure to twist the spout as you pull so as not to loosen any pipe connections inside the wall. From there, simply slide on the new spout and tighten the setscrew. Voila!
Drain keys or drain extractors are handy tools that can be used to remove a drain cover without having to remove the entire drain assembly. They come with reverse-thread systems or expanding wings that grip the flange firmly from the inside. Once the tool grips the flange, you can use a wrench to turn it and remove the drain cover.
Do you need teflon tape on tub spout?
When making a threaded connection, be sure to clean the threads on both the fitting and the pipe. Apply pipe joint compound or Teflon tape to the threads to create a seal. We prefer Teflon tape because it is cleaner and less messy.
When shopping for a tub spout, it’s important to pay attention to the size (length) of the spout, as there can be variations in each type (threaded or slip). Not every store carries every length in each type, so it’s important to be patient when shopping around. When we refer to size, we’re referring to the length of the spout, not the overall length of the spout.
What size is the thread on a bath spout
If you are replacing a tub spout with a new one, be sure to measure the length of the pipe coming out from your wall. The new tub spout should be 4″ to 4-3/8″ in order to avoid a gap between the wall and the spout. The new tub spout should also have a threaded nose 1/2 inch IPS inside thread, and be 5-1/4″ in length.
Moen makes two different versions of tub spouts. Its iron-pipe size, or IPS, screws onto 1/2-inch male threaded pipe. Its slip-fit tub spout attaches to 1/2-inch copper tubing and is held in place with a hex-screw.
How do you remove a Danco tub spout?
To remove an old Tub Spout, first turn it counterclockwise. If there is a set screw holding it in place, be sure to remove that prior to rotating the Spout off. If the Spout is hard to remove, you may need to use the end of a hammer or large wrench to help loosen while turning.
Set screws are typically used to secure an object in place byThreading into a tapped hole Or by Engaging with a keyway in a rotating part.
Grub screws are similar to set screws in that they are also used to secure an object in place, but they differ in that they have no head and are instead inserted into a blind hole.
Conclusion
There is no definitive answer to this question as it depends on the specific tub and spout involved. However, in general, a rear threaded tub spout is one where the threading is located at the back of the spout, as opposed to the front or side. This can make it more difficult to access and install, but it may also provide a more secure connection.
Rear threaded tub spouts are an easy way to update your bathroom. They are simple to install and come in a variety of styles. With a little bit of research, you can find the perfect rear threaded tub spout for your bathroom.