A “rough-in” is the distance from a wall or other obstruction to the center of the toilet drain. A standard rough-in is 12 inches. This allows for plenty of room to install the drain and the necessary cleanout access behind the toilet.
The term “rough in” refers to the distance from the wall behind the toilet to the centerline of the drain pipe. Most toilets have a standard rough in of 12 inches, but it can vary from 10 to 14 inches. To determine the rough in for your toilet, measure from the back wall to the centerline of the drain pipe.
Table of Contents
How do you measure rough-in toilet?
When measuring the rough-in for your toilet, you want to measure from the wall behind the toilet to the middle of the closet bolt caps on your current toilet. The closet bolts are the bolts holding your toilet to the floor. If you have baseboards or tiling on the wall behind the toilet, do not include those in your measurement.
The numbers mentioned in the topic refer to the distance between the wall and the center of the closet flange. Toilet bowls usually work with either a 10″ or a 12″ distance, but a 10″ rough tank is slimmer to allow for the decreased distance.
What does 12-inch rough-in toilet mean
The term “12-inch rough-in” means that the distance from the center of the toilet flange to the finished back wall is 12 inches. This information can be found on the toilet’s specification sheet.
If you have a 10-inch rough-in for your bathroom plumbing, you can still install a toilet designed for a 12-inch rough-in. This is because the toilet’s rough-in is designed to match the rough-in for your bathroom plumbing. However, if you have a 12-inch rough-in, you may need to install a larger toilet to accommodate the increased space.
Does rough in have to be exact?
To measure a toilet’s rough-in distance, simply measure the distance from the center of the drainpipe to the back wall. You’ll need a tape measure for this, and it’s best to measure from the floor to the center of the drainpipe, since the back wall may not be perfectly level. Once you have your measurement, be sure to write it down or take a picture of it so you don’t forget!
If the flush valve drain opening at the bottom of your tank looks about the size of a baseball or orange, you need a 2″ flapper. If the opening looks about the size of a softball or grapefruit, you need a 3″ flapper.
How do I know if I need a 10 or 12 in toilet?
The old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard) There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline If your measurements are between 115 and 125 inches, it is a 12-inch rough-in.
The one-piece toilet is a great option for small bathrooms because it takes up less space. It is also more durable than a two-piece toilet because it is made of one solid piece of ceramic. The one-piece toilet is easier to clean because there are fewer exposed plumbing or flushing elements.
Can you use a 12-inch toilet with a 10 inch rough-in
If you have a 10” rough-in size in your bathroom, you will need to find a toilet that is specifically made for that rough-in size. You cannot use a 12” rough-in toilet in a 10” rough-in, as it will not fit.
Most people find elongated toilet bowls to be more comfortable, but in a small bathroom, a round bowl can save space. Elongated toilet bowls measure up to 31″ from the wall, while round fixtures max out at 28″. Because round bowls are less expensive than elongated bowls, they save a few dollars, too.
What is the minimum distance from toilet to wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. There should be at least 24 inches of clear space in front of a toilet or bidet.
When measuring for a new toilet, the most important measurement is the rough-in dimension. This is the distance between the bolts that hold the toilet to the floor and the wall. Make sure you measure from the centre of the bolts, up to the drywall (as opposed to the baseboard). This will ensure that your new toilet will fit in the space correctly.
Are all toilet drains the same distance from the wall
The rough-in distance for a toilet drain is the distance from the center of the drain to the closest wall. The rough-in distance for a toilet in a newer home is 12 inches, while the rough-in distance for a toilet in an older home is anything between 10 and 14 inches. A wall-mounted toilet also needs a 10 inch thick wall to accommodate the flushing system.
When measuring for a new toilet, start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s best to perform this measurement before you remove the old toilet. This will ensure that the new toilet will fit in your space.
How much does it cost to rough-in a toilet?
How do you price a job?
Formulating a pricing strategyTake your cost of goods sold (COGS) and add a healthy profit margin to determine your price.Apply hikes and discounts as necessary so that your price aligns with your goals.Remember to consider shipping and other “out-of-pocket” expenses.
How much does it cost to rough in a city block?
Avg. Rough-in Cost The average home has an average of 10 foundation walls and the average cost of hiring a professional is $300 per block or $30 per linear foot. This job would cost approximately $3,000 for a professional to complete.
What does a rough in include?
Every rough-in installation is different but, in general, the rough-in stage consists of the installation of pipes, vents and the framing necessary to support your fixtures. Once everything is in place, the walls and ceilings can be sheetrocked, mudded and textured, and plumbing fixtures can be installed.
How much does a rough in cost per month?
Based on the price of an average rent rate of $287, a target of $350 per hole should offset the monthly expense of paying
A plumbing rough-in is a great way to get all of the plumbing work done for a new construction project. This includes running all of the water lines and drains through the studs and framing members, and making all of the connections. It’s a good idea to do this before installing any sinks, faucets, or other fixtures.
Warp Up
The term “rough in” refers to the distance from the finished wall to the center of the toilet flange. This measurement is important when installing a toilet, as the bowl must be properly positioned over the flange in order to function correctly.
A “rough in” for a toilet is the distance from the back wall to the centerline of the drain. Most toilets have a standard rough in of 12 inches, but some may be 10 or 14 inches. Toilet rough in measurements are important when selecting a toilet to ensure that it will fit properly in your bathroom.