If you’re planning to install a new toilet, or replace an old one, you’ll need to know the distance from the wall to the center of the waste outlet. This measurement is called the rough-in. Most toilets have a rough-in of 12 inches, but it can range from 10 to 14 inches. To determine your toilet’s rough-in, measure from the wall to the center of the bolts that hold the toilet to the floor.
There is no definitive answer to this question as the size of toilets can vary significantly. However, a rough guide would be to measure approximately 30cm from the wall to the centre of the toilet bowl.
Table of Contents
How far should a toilet be from the wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture (The NKBA actually recommends 32 inches). There should be at least 24 inches of clear space in front of a toilet or bidet.
If you’re looking for a new toilet, be aware that most toilets will have a 12 inch rough-in. Toilets with a 10- or 14-inch rough-in measurement are a little less common, so you might have less of a selection to choose from. When replacing an existing toilet, look for a replacement toilet with the same rough-in measurement.
How far should toilet flange be from wall
The center of the water closet flange should be 12-inches from the back wall. When you measure this distance, make sure you measure from the finished wall and not the base molding. Another thing you need to consider is the thickness of your back wall. If you used ½” drywall, add an extra ½”.
The clearance from the center of the toilet to any adjacent fixture or sidewall is 15 inches. That’s the minimum (you can have more). So looking at the toilet, make sure there are at least 15 inches of clearance from the center of the toilet to any adjacent fixture (or wall).
When the toilet is too far from the wall?
If you’re having trouble with your toilet being too far from the wall, you may want to consider using an offset flange. This will require you to remove the toilet, as well as the subfloor and slab around the toilet. You’ll also need to change the direction of the plumbing pipes.
If you’re replacing an old toilet, you’ll need to know the rough-in size. This is the distance from the center of the capped bolts on the bottom of the toilet to the wall (not the baseboard). The rough-in size will determine the size of the new toilet you need to purchase.
As a guideline, there should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side. If your measurements are between 115 and 125 inches, it is a 12-inch rough-in.
What does 12 inch rough-in mean when installing a toilet?
The rough-in distance is an important measurement to take when installing a toilet. This is the distance from the wall behind the toilet to the center of the drain opening. This measurement is important because it tells you how much room the toilet needs to fit comfortably, allowing adequate space between the wall and the tank.
One of the best places to hang artwork in a bathroom is above the toilet. Toilets sit lower on the wall so unless there is a window above, you typically have an abundance of wall space. A long piece of art should be hung so that the bottom is at least 6″-8″ above the lid of the tank.
How far does an elongated toilet stick out from the wall
If you have a small bathroom, you may want to consider a round toilet bowl to save space. Elongated toilet bowls can be up to 31″ from the wall, while round fixtures max out at 28″. Round bowls are also less expensive than elongated bowls, so you can save a few dollars as well.
The standard toilet rough-in is 12 inches, but you should always measure before assuming that your bathroom has this standard size. Some older homes come with 10” or 14” rough-in sizes. You may also find 10” rough-in sizes in powder rooms, half baths, or other small bathrooms to save space.
How far from the wall should a toilet soil pipe be?
The distance between a wall and a toilet is generally 300mm, so you will need to add an extra 300mm to that measurement to allow for the WC waste connector to be fitted.
Toilet code clearance requirements are important to follow in order to ensure proper spacing and design in your bathroom. At least 15 inches from the center of your toilet to any side wall or partition is required, as well as a 30 inch center to center distance from an adjacent toilet fixture. You must also have a least 21 inches of clearance from a wall, fixture or door. Following these code requirements will help create a functional and safe bathroom space.
Can a toilet be moved 6 inches
If you need to move your toilet, you can do so without having to make a new hole in the floor. An offset toilet flange will allow you to move the toilet by a couple of inches on any side. This will allow you to use the same wastewater line, which will help save you money.
If you need to move your toilet a couple of inches in any direction, you can use an offset toilet flange. This will allow you to avoid having to cut a new hole in the floor or reconstruct the waste water pipe.
Should a toilet touch the wall?
A 2–1/2′ gap between the toilet tank and the wall behind it is fine. There is no need to fill the gap with anything, as it will not affect the function of the toilet.
If your toilet was manufactured after 2005, it is likely that it has a three inch flapper. However, if your toilet is older, it is likely that it has a two inch flapper. You can easily determine the size of your toilet’s flapper by looking at the flush valve drain opening at the bottom of your tank.
How do I know if my toilet is 2 or 3 inches
If the flush valve drain opening at the bottom of your tank looks about the size of a baseball or orange, you need a 2″ flapper. If the opening looks about the size of a softball or grapefruit, you need a 3″ flapper.
When measuring for a new toilet, it is important to know whether you have a round or elongated bowl. A round toilet bowl will measure approximately 16 ½” in length, while an elongated bowl is approximately 18 ½” in length. To get an accurate measurement, place the hook of your tape measure at the midpoint and measure to the outside edge of the toilet bowl rim in front.
Where should the rough in measurement for a toilet start
You will need a water closet with a 10-inch roughen and 15 inches of clearance.
When measuring for a toilet’s rough-in distance, it is important to take into account the baseboard and not measure from it. This will help ensure an accurate measurement and avoid buying the wrong fixture for your bathroom.
Warp Up
The standard toilet dimensions are about 12 inches from the wall.
There are a few things to keep in mind when measuring for a toilet. First, you’ll need to measure the distance from the wall to the center of the flange. Second, you’ll need to measure the distance from the floor to the top of the flange. Finally, you’ll need to measure the height of the toilet itself. With these three measurements, you’ll be able to determine the best size toilet for your space.