Draw a line on your wall about 14″ above the floor.This is where the top of the toilet tank will be installed. Most toilets come with a tank, but some are all-in-one units. Find the center of the closet bolts (where the tank bolts to the bowl).This is where you will make your mark for the center of the closet flange (the large drain pipe fitting that is sealed to the floor). The center of the closet flange should be 12″ from the finished wall. Use a level to make sure your line is level before you make any marks. Once you have the level line, you are ready to make your mark for the center of the closet flange.
10 inches from the back wall to the center of the toilet flange
12 inches from the side wall to the center of the toilet flange
Table of Contents
How do I know if I need a 10 or 12 rough in toilet?
If you’re considering replacing your toilet, it’s important to know the rough-in size. This is the distance from the center of the drain to the wall. Most toilets have a 12-inch rough-in, but some may have a 10-inch or 14-inch rough-in. Toilet rough-ins are usually either right-hand or left-hand, depending on the location of the flush handle. Measuring the rough-in size is simple. Just measure from the center of the drain to the wall. If your measurements are between 115 and 125 inches, it is a 12-inch rough-in.
The standard distance from the back wall for a toilet flange is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. This measurement is important because it ensures that the flange is properly positioned and won’t be too close to the wall framing.
Where should the rough in measurement for a toilet start
You will need a water closet with a 10-inch roughen and 15 inches of clearance.
eHow may earn compensation through affiliate links in this story. Ideally, the toilet’s rough-in should match the rough-in for your bathroom plumbing. However, even if a toilet is designed for a 10-inch rough-in, you can still install it into a space that has a 12-inch rough-in.
Are most toilets 12 inches from wall?
Most toilets will have a 12 inch rough-in. Toilets with a 10- or 14-inch rough-in measurement are a little less common, so you might have less of a selection of toilets of this size.
The center of the water closet flange should be 12-inches from the back wall. When you measure this distance, make sure you measure from the finished wall and not the base molding. Another thing you need to consider is the thickness of your back wall. If you used ½” drywall, add an extra ½”.
What is code for distance in front of toilet?
Bathroom building code typically says that toilets need at least 21 inches of clearance in front of the toilet. While it is not required, opting for 30 inches of room provides a more comfortable space. Side-to-side clearance: a minimum of 15 inches from the center-line of the toilet to the nearest obstruction.
I agree that it is a waste of space to have a TV in the corner of a room. It would be better to put it in its own little room so it doesn’t take up valuable space in the room.
What is the difference between a 10 inch and 12 inch rough in toilet
Most toilet bowls will work with either a 10″ or a 12″ distance between the wall and the center of the closet flange. A 10″ rough tank is slimmer to allow for the decreased distance.
The standard toilet rough-in size is 12 inches, but you should always measure the rough-in before assuming that it is 12 inches. Some older homes have 10” or 14” rough-in sizes. You may also find 10” rough-in sizes in powder rooms, half baths, or other small bathrooms where space is limited.
Does rough-in have to be exact?
When measuring a toilet’s rough-in distance, it is important to account for the baseboard. Measuring from the baseboard will result in an inaccurate measurement.
The maximum MaP rating is 1,000. As I said, we only install toilets with a MaP rating of 800 or more. We have found that those toilets flush very well with little or no problems to the consumer. However, if you try hard enough, you can clog any toilet.
How much space is behind a 12 in rough-in toilet
The measurement of 12-inches for a toilet rough-in refers to the distance between the center of the toilet flange to the finished back wall. This is important to know when selecting a toilet as it must fit within the rough-in dimensions. The standard rough-in size for toilets is 12-inches, so most toilets will accommodate this measurement.
If the toilet is within six feet of the stack and the waste line is 3 inches in diameter, tie the waste line from the new toilet directly into the stack. If the waste line is 4 inches in diameter, the toilet can be as far as 10 feet from the stack.
What width do you need to leave for a toilet?
The size of the sanitaryware is important as it needs to be big enough to be comfortable and functional. The toilet and bidets must have a minimum space of 70cm in width and 120cm in length. If they are next to a wall, the minimum free space should be 20cm, and if there is an element on their side, they should not be placed less than 15cm away for greater usability.
A three inch flapper is typically found in newer toilets manufactured since 2005. An easy reference for determining your toilet’s flapper size is to look at the flush valve drain opening at the bottom of your tank.
How many inches above a toilet should you hang a picture
The bathroom is one of the best places to hang artwork because there is typically a lot of wall space above the toilet. A long piece of art should be hung so that the bottom is at least 6″-8″ above the lid of the tank.
If you’re over 6 feet tall, toilets taller than 19 inches are optimal for you. Extra tall versions are typically 20 to 21 inches from floor to bowl, but they’re compact enough to fit in the standard private bathroom.
Does toilet flange go on top of tile or flush
If you install the toilet flange flush with the finished floor, or even below the finished floor, leak paths will form, because the flange won’t be at the correct height to accept the horn at the bottom of the toilet. A best practice is to install the toilet flange on top of the finished floor.
The optimum flange height to aim for when installing a toilet is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
Final Words
The “rough in” measurements for a toilet are the distance from the back wall to the center of the drain, and the distance from the floor to the top of the flange. These measurements can vary depending on the specific toilet model.
There are a few different measurements that need to be taken into consideration when Roughing-In a toilet. First, you’ll need to measure the distance from the center of the drain to the back wall and to the side wall. Next, you’ll need to measure the distance from the floor to the center of the drain. Lastly, you’ll need to measure the distance from the floor to the side wall. These measurements will ensure that your toilet is installed properly and will function as it should.