Skip to content

Toilet with 10 inch rough?

  • by

Are you looking for a toilet with a 10-inch rough-in? This measurement is the distance from the wall behind the toilet to the center of the outlet hole. A 10-inch rough-in is common, but if your home has a 12-inch rough-in, don’t worry, we have toilets to fit that too!

There is no such thing as a toilet with a 10 inch rough.

Can you put a 10-inch rough in toilet?

If you’re looking to install a new toilet in your bathroom, be sure to check the rough-in size first. A 10-inch rough-in toilet can fit into a 12-inch rough-in (though a longer connector may be needed), but a 12-inch rough-in toilet will not fit in a bathroom with a 10-inch rough-in size.

If you’re looking to replace an old toilet or install a new one, you’ll need to know the rough-in measurement. This is the distance from the wall to the center of the drainpipe. The most common rough-in measurement is 10 inches, but you may encounter a 12-inch rough-in. Most toilets that you’ll find in retail outlets have a 12-inch rough-in.

How do I know if I need a 10 or 12 rough in toilet

The old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard) There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 115 and 125 inches, it is a 12-inch rough-in.

See also  Shut off valves under sink?

The rough in dimensions for a toilet refer to the space between the wall behind the toilet and the center of the waste pipe. Standard rough in dimensions for toilets are 12 inches, but in some cases they can be anywhere from 10 to 14 inches. It’s important to know the rough in dimensions for your toilet before you install it, so that you can make sure it will fit in the space you have available.

Does toilet rough-in size matter?

When measuring for a new toilet, you will want to start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It is best to perform this measurement before you remove the old toilet. This will help to ensure that the new toilet you select will fit properly in the space.

There are two main types of toilets- rough in and close coupled. Rough in toilets have a distance of 10 or 12 inches from the wall to the center of the closet flange. Close coupled toilets have the tank attached directly to the bowl, which is why they are more compact. Most toilet bowls will work with either a 10 or 12 inch rough in, but a 10 inch rough in is slimmer to allow for the decreased distance.

Is a 1 piece or 2 piece toilet better?

If you’re looking for a more durable toilet option, you may want to consider a one-piece model. These toilets are made of a single solid piece of ceramic, with fewer exposed plumbing or flushing elements. This can be a great choice for small bathrooms where space is limited.

See also  Anti clog toilet?

This is an important measurement to take when considering a new toilet, as you want to make sure there is enough clearance for comfortable use. Make sure to measure from the center of the toilet to the nearest wall or fixture, and add at least 15 inches for clearance.

What is code for distance around a toilet

Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. The NKBA actually recommends 32 inches.

There are elongated toilets built to fit a 10” rough-in, and some are built to fit 14”. The bydefault size for a new toilet installation is 12”. If you have a smaller bathroom, you may want to consider a 10” rough-in toilet. If you have a larger bathroom, you may want to consider a 14” rough-in toilet.

How do I know if my toilet is 2 or 3 inches?

If the flush valve on your toilet tank is leaking, you may need to replace the flapper. The size of the flapper you need depends on the size of the drain opening on the bottom of the tank. If the opening is about the size of a baseball or orange, you will need a 2″ flapper. If the opening is about the size of a softball or grapefruit, you will need a 3″ flapper.

When tightening the bolts on a toilet, it is important to be conservative and not to overtighten. Try turning each bolt a quarter turn at a time until you feel resistance. If the toilet bowl does not move when you try to wiggle it, then the bolts are probably tight enough. This is a “feel” thing that you get from experience, so be conservative and use your best judgement.

See also  Can you get hiv from toilet paper?

Are all toilet drains the same distance from the wall

The rough-in distance for newer homes from the wall to the center of the toilet drain is 12-inch, while older homes have a distance of anything between 10- or 14 inches. A wall-mounted toilet also needs a 10 inch thick wall to accommodate the flushing system.

If you’re looking for an excellent performing toilet, make sure to check the score. Toilets with a score of 500 and above are sure to provide you with the level of performance you’re looking for.

Which is more comfortable round or elongated toilet?

While most people might find elongated toilet bowls to be more comfortable, in a small bathroom, a round bowl can actually save some space. Elongated toilet bowls measure up to 31″ from the wall, while round fixtures typically max out at 28″ So, if you’re tight on space in your bathroom, going with a round bowl could give you a few extra inches. Plus, round bowls are usually less expensive than elongated bowls, so you could save a few dollars as well.

common signs that your toilet needs to be replaced include:

• leaking or persistent dripping

• cracks in the bowl or tank

• grungy, stained porcelain

• loose bolts or hardware

• wobbling or rocking

• constantly running water

• weak flush

• slow drainage

Warp Up

This is a difficult question to answer without more information. If you are talking about a toilet with a 10 inch rough, it is likely that you will need a special size of toilet. You may be able to find a 10 inch rough inlet version of a toilet, but it is not a common size. You may want to consider changing the size of your rough inlet, or finding a different type of toilet altogether.

Overall, the 10 inch rough toilet is a good product. It has a few minor issues, but nothing that would deter someone from purchasing it. The biggest issues are the price and the lack of a clear instructions. The price is a bit high, but it is worth it for a quality product. The lack of clear instructions could be a problem for some, but most people should be able to figure it out.