Skip to content

What does 12 rough in mean for toilet?

When it comes to toilets, the term “rough in” refers to the distance from the back wall to the centerline of the floor drain or the flange that mounts the toilet. A standard rough in is 12 inches, but there are also 10- and 14-inch rough ins. Toilets with a 12-inch rough in will fit into a space that is 24 inches wide.

Rough in refers to the distance from the finished wall to the center of the drain. For a toilet, the rough in is typically 12 inches.

Can you replace a 12-inch rough in toilet with a 10-inch rough in toilet?

This is because the 12” rough-in toilet is too big to fit in the 10” rough-in size. The 10” rough-in toilet can fit into a 12” rough-in size, but a longer connector may be needed.

If you’re planning on replacing your old toilet, you’ll need to measure the rough-in to see what size you need. The rough-in is the distance from the center of the bolts on the bottom of the toilet to the wall. For a standard 12-inch rough-in, you’ll need a minimum of 115 inches and a maximum of 125 inches.

How do you measure rough in toilet

If you’re planning on replacing your old toilet, make sure to measure the rough-in size first. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s important to do this measurement before removing the old toilet so you know what size will fit in your space.

See also  How much does a running toilet cost in water?

The rough-in is the distance from the center of the water outlet to the wall behind the toilet. This is important to know when shopping for a toilet because you need to make sure the bowl is the right size for the rough-in. In some cases, the rough-in is in the wall, but we won’t be covering those toilets here.

Are most toilets 12 rough-in?

If you’re looking for a replacement toilet, be sure to check the rough-in measurement. Most toilets will have a 12 inch rough-in, but toilets with a 10- or 14-inch rough-in measurement are a little less common. You might have less of a selection of toilets of this size, so be sure to measure your rough-in before you shop.

Most codes require a minimum of 15 inches from any side wall or obstruction (measured from the center of the toilet) and not closer than 30 inches center to center to any other sanitary fixture.

How do I know if my toilet is 2 or 3 inches?

If the flush valve drain opening at the bottom of your tank looks about the size of a baseball or orange, you need a 2″ flapper. If the opening looks about the size of a softball or grapefruit, you need a 3″ flapper.

A toilet tank’s height is measured from the floor to the top of the toilet tank. Place the end of the tape measure on the floor, and take the measurement at the very top edge of the tank lid. Toilet bowls and seats are either round or oval.

How do I know if my toilet is biscuit or almond

Almond is a type of tree nut that is lighter in color than other nuts. When heated, almond objects tend to darken in color. This is due to the fact that the tree nut contains a natural pigment called cyanidin.

See also  Clawfoot tub add a shower?

If you’re measuring for a new toilet, you’ll need to know the rough-in distance. This is the distance from the wall to the center of the drain pipe. To get an accurate measurement, don’t measure from the baseboard. Instead, account for the baseboard by measuring from the wall to the edge of the baseboard, and then add the thickness of the baseboard to your measurement.

Should toilet flange be flush with floor?

It is always best to install the toilet flange on top of the finished floor. If the flange is installed flush with the finished floor, or even below the finished floor, leak paths can form. This is because the flange will not be at the correct height to accept the horn at the bottom of the toilet.

An S-trap is an S-shaped trap between the toilet outlet and the sewer system. It is connected to the drainpipe through the floor. On the other hand, a P-trap is shaped like the letter P and is connected to the drainage system through an opening in the wall.

How do I know what size toilet seat to buy

To determine the distance between the center of the mounting holes in the back of the toilet, use a tape measure. The standard measurement for this distance is 5 ½”, with a midpoint of approximately 2 ¾”. Place the hook of your tape measure at the midpoint and measure to the outside edge of the toilet bowl rim in front.

Cotton balls, cotton pads, and Q-Tips should not be flushed down the toilet as they do not break down and will clump together, causing problems in your pipes.

Are most toilets 2 or 3 inch?

The two inch flapper is the most common size used in toilets, but three inch flappers have become popular in recent years. You can easily determine your toilet’s flapper size by looking at the flush valve drain opening at the bottom of the tank.

See also  Great value toilet cleaner?

The stack is the main pipe that carries all the waste water from the house. Toilet waste lines should be tied directly into the stack if the toilet is within six feet of it and the waste line is 3 inches in diameter. If the waste line is 4 inches in diameter, the toilet can be as far as 10 feet from the stack. This is to ensure that all the waste water goes into the stack and not around it.

Should a toilet be flush with the wall

The toilet flange must be at least 15 inches away from any sidewall or nearby fixture. However, 15 inches is the absolute minimum. A 15-inch distance from the vanity, shower, tub, and back and side walls is required to accommodate the toilet flange.

The clearance from the center of the toilet to any adjacent fixture or sidewall is 15 inches. That’s the minimum (you can have more). So looking at the toilet, make sure there are at least 15 inches of clearance from the center of the toilet to any adjacent fixture (or wall).

Can you replace a 11 inch rough in toilet with a 12 inch rough in toilet

The term “rough-in” refers to the distance from the wall behind the toilet to the centerline of the closet bolts. A standard rough-in is 12 inches, but toilets can be found that have a 10-inch or 14-inch rough-in. If you are replacing an old toilet, chances are good that it has a 12-inch rough-in. You can, however, install a toilet with a 10-inch or 14-inch rough-in into a space that has a 12-inch rough-in. The extra space will simply be filled with filler material.

Comfort height toilets are designed to be taller than standard toilets, typically by 2-3 inches. This makes them more comfortable for taller people to use, as they do not have to stoop down as much. Standard toilets are less than 17 inches high, making them more suitable for shorter people.

Final Words

A 12 rough in for a toilet means that the toilet is 12 inches from the wall.

In conclusion, a 12 rough in for a toilet means that the distance from the wall to the center of the floor drain is 12 inches.