The term “12-inch rough-in toilet” refers to the distance from the wall behind the toilet to the centerline of the drainpipe. This measurement is important when selecting a new toilet because the drainpipe must line up with the hole in the floor or subfloor. Most toilets have a 12-inch rough-in, but some models are available with a 10- or 14-inch rough-in.
A 12-inch rough in toilet is a type of toilet that has a rough in measurement of 12 inches. This means that the distance from the center of the drain to the back wall of the toilet is 12 inches. This is a standard size for many toilets, but it is always best to check the specific measurements of your toilet before purchasing a new one.
Table of Contents
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard) There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 115 and 125 inches, it is a 12-inch rough-in.
If you have a 10” rough-in in your bathroom, you will need to use a toilet with a 10” rough-in. A 12” rough-in toilet will not fit in a bathroom with a 10” rough-in size.
Can you replace a 11 inch rough in toilet with a 12-inch rough in toilet
If you have a 10-inch rough-in for your bathroom plumbing, you can still install a toilet designed for a 12-inch rough-in. This is because the extra space will allow you to make any necessary adjustments to the toilet during installation. However, it is important to note that you may need to make some modifications to the toilet itself in order to make it fit properly.
There are a few different measurements that you need to take into account when performing a toilet rough-in. The first is the rough-in size, which is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s important to take this measurement before you remove the old toilet so that you have a reference point.
The second measurement is the distance from the center of the drainpipe to the edge of the toilet flange. This will determine how far you need to offset the drainpipe when you install the new toilet.
Finally, you need to measure the distance between the bolts that hold the toilet to the floor. This will determine the size of the flange that you need to install.
Once you have all of these measurements, you can start to install the new toilet. Make sure that you offset the drainpipe according to the second measurement, and that you install the flange at the correct distance from the bolts.
Are most toilets 12 inches from wall?
If you’re looking for toilets with a 10- or 14-inch rough-in measurement, you might have less of a selection to choose from than if you’re looking for toilets with a 12-inch rough-in measurement. However, there are still a number of toilets available with these rough-in measurements, so you should be able to find one that meets your needs.
The flush valve drain opening is located at the bottom of your tank. If the opening looks about the size of a baseball or orange, you need a 2″ flapper. If the opening looks about the size of a softball or grapefruit, you need a 3″ flapper.
How many inches should a toilet be away from the wall?
Most codes require a toilet to be a certain distance from any side wall or obstruction, and also to be a certain distance from any other sanitary fixture. The NKBA recommends a toilet to be 32 inches away from any other fixture.
There are many reasons to prefer elongated bowls over other types of toilet bowls. Elongated bowls are considered more ‘hygienic’ because the larger surface area of the bowl makes it easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
How far to rough in a toilet off the wall
The standard distance from the back wall is 12 inches, which is the same as the minimum distance from the front wall. The only time you would need more space in front of the toilet is if you have a larger bathroom and need more room to move around.
This is a difficult and expensive project. If you are just moving the toilet a couple of inches, it may be easier to demo the concrete and rebuild the foundation than to try to move the water and waste lines. You will also need to replace the sub-flooring, flooring, and fixtures.
Can I move my toilet over a few inches?
Yes, it is possible to move a toilet without having to make a new hole in the floor. You can use an offset toilet flange to move the toilet by a couple of inches on any side. This will allow you to use the same wastewater line and in turn help to save you a lot of money.
When measuring a toilet’s rough-in distance, it’s important to be accurate in order to avoid purchasing the wrong fixture for your bathroom. Here are some tips to help you get it right:
-Don’t measure from the baseboard; account for it instead.
-Take into account the location of the drainpipe and any other obstacles that might impede the installation of the toilet.
-Measure from the back wall to the center of the drainpipe to get the most accurate measurement.
How do I choose the right size toilet
Standard rough-in dimensions for toilets is 12-inches. A distance of 10-inches or 14-inches is occasionally found in small bathrooms or older homes. To determine your bathroom’s rough-in, measure from the wall behind the toilet to the middle of the bolts on the base of the toilet.
There are two main types of traps used in toilets – S-traps and P-traps.
S-traps are S-shaped traps between the toilet outlet and the sewer system. They are connected to the drainpipe through the floor.
P-traps are shaped like the letter P and are connected to the drainage system through an opening in the wall.
Are most toilets 2 or 3 inch?
The size of a toilet’s flapper is determined by the size of the flush valve drain opening at the bottom of the tank. Most toilets will use the two inch flapper; however, three inch flappers have become popular in recent years and can be found in newer toilets manufactured since 2005. An easy reference for determining your toilet’s flapper size is to look at the flush valve drain opening.
When it comes to the gap between a toilet and shower, it is recommended that you have at least an 18-inch gap at the side of the toilet and 30 inches in front so that it is easy to clean and use. This will also allow whoever is using the shower to do so safely and comfortably.
How many inches above a toilet should you hang a picture
One of the best places to hang artwork in a bathroom is above the toilet. Toilets sit lower on the wall so unless there is a window above, you typically have an abundance of wall space. A long piece of art should be hung so that the bottom is at least 6″-8″ above the lid of the tank.
The one-piece toilet is a great option for small bathrooms where space is at a premium. It is also more durable than the two-piece toilet, since it is made of one solid piece of ceramic with fewer exposed plumbing or flushing elements.
What is comfort height vs standard toilet
There are a few reasons why comfort height toilets are becoming a popular option for many households. One reason is that they are more comfortable than traditional toilets. The higher seat makes it easier to sit down and stand up, and the extra height can help reduce back pain. Additionally, comfort height toilets are often easier to clean than traditional toilets, since there is less chance of getting dirt and grime on your clothing. Finally, comfort height toilets can give the illusion of a larger bathroom, since they make the room appear taller.
There are both pros and cons to having a taller toilet bowl. For some people, it can be very comfortable and offer many advantages. However, for others, it may not be as comfortable. Ultimately, it is up to the individual to decide what is best for them.
Final Words
A 12-inch rough in toilet is a toilet that has a distance of 12 inches from the center of the drain to the wall behind it. This is the standard size for most toilets, so if you’re looking for a replacement toilet, you’ll likely want to get one with a 12-inch rough in.
A 12 inch rough in toilet is a toilet that has a 12 inch space between the wall and the center of the drain. This is the standard size for most toilets, but there are some that are smaller or larger. If you are buying a new toilet, make sure to measure the rough in so you can buy the correct size.